1. Introduction

718H is one of the most widely‑used pre‑hardened nickel‑alloy mold steels across global mold‑making workshops, equivalent to DIN 1.2738 / GB 3Cr2MnNiMo, well‑known as the upgraded variant of P20 mold steel.
Delivered in pre‑hardened condition without customer‑side heat treatment, 718H features consistent hardness across thick blocks, reliable polish‑and‑texturing performance, decent toughness and balanced cost‑performance. Manufacturers frequently order 718H mold blocks for complete workflow: saw cutting, CNC hard milling, EDM, texture etching, high‑gloss polishing and final mold assembly. It fits medium‑to‑high volume plastic injection molds for visible cosmetic parts.
Even so, mold shops often run into practical headaches: premature tool wear during hard milling, uneven polishing marks on large mold inserts, dimensional shift after finishing, or texture‑etching blemishes caused by poor steel purity. Fabricators need to understand material limits and adjust CNC strategies accordingly.
2. What Is 718H Mold Steel?
718H belongs to nickel‑enhanced pre‑hardened plastic mold steel, often referenced as P20+Ni. Its typical as‑delivered hardness sits at 32‑38 HRC after factory quenching and tempering, no further hardening heat treatment required before machining.
Many buyers confuse standard 718 and 718H. 718H represents the higher‑hardness, higher‑purity version for long‑run production molds. On purchase orders and engineering drawings, write full grade “718H” together with material specification DIN 1.2738 rather than short informal names, to avoid receiving lower‑grade substitute steel for your injection mold components.
718H is not corrosion‑resistant stainless mold steel. It is not designed for heavy‑duty conditions with high‑glass‑fiber filled plastics or corrosive PVC melt without extra surface treatment such as nitriding or chrome plating.
3. Key Material Properties of 718H Mold Steel
Property 718H Mold Steel Characteristics
Material type Nickel‑alloy pre‑hardened plastic mold steel
Hardness (Delivery state) 32‑38 HRC, uniform through thick cross‑sections
Machinability Moderate; requires coated carbide cutting tools for hard milling
Polish & Texturing Excellent; supports high‑gloss polish and fine VDI / Mold‑Tech texture etching
Toughness Good; resists chipping for deep‑cavity, thin‑rib mold inserts
Cost Mid‑range, higher than P20 but lower than NAK80 mirror steel
Common stock forms Mold block, thick plate, round bar
Thanks to uniform hardness throughout large‑size blocks, 718H solves a well‑known pain point of standard P20: soft core zones inside thick mold plates which cause uneven wear and inconsistent surface finish over production cycles. That makes 718H the go‑to choice for large automotive and home‑appearance mold projects.
4. Typical Applications for 718H Mold Steel
718H dominates medium‑and‑large plastic injection mold manufacturing. Representative use‑cases cover automotive interior trims, home‑appliance housings, cosmetic packaging, consumer‑electronic shells and general‑purpose appearance mold inserts. Pre‑hardened mold blocks are the most common procurement form.
Its balanced polishability and texturing capability supports both glossy cosmetic surfaces and matte leather‑grain textures. The full production workflow includes block sawing, CNC hard milling, EDM, texture etching, hand polishing and mold fitting. Customers frequently source finished mold bases and machined inserts rather than raw steel only.
For projects targeting 300,000‑800,000 molding shots with visible cosmetic requirements, 718H delivers stable output without the high premium of mirror‑grade steels like NAK80.
5. CNC Machining Guidance for 718H Mold Steel
718H can be processed with CNC milling, drilling, turning and electrical discharge machining. However, machining quality depends not merely on machine power; raw block internal stress, machining allowance, clamping rigidity, cutting‑tool grade and cutting parameters all strongly affect final results. Deep‑cavity thin‑rib mold inserts are particularly prone to tool chatter, tool abrasion and dimensional distortion after finishing cuts.
A standard process route for large 718H mold blocks:
Mold Block Sawing → Stress‑relief Treatment → CNC Rough Milling → Semi‑Finishing → Stress Release → Hard‑Milling Finishing → EDM / Texture Etching → Polishing → Mold Assembly
Key Pitfalls for CNC Milling 718H Mold Steel
Chatter and accelerated tool wear are the two most frequent complaints when milling pre‑hardened 718H. Chatter manifests as high‑frequency noise, tool vibration, wavy tool marks on mold cavity surfaces. Problems stem from the whole machining chain: machine spindle, cutting tool, tool holder, fixture and workpiece rigidity.
1. Workpiece rigidity risk: Thin‑rib, deep‑cavity mold inserts deflect under cutting force. Simply swapping cutters cannot fully eliminate chatter. Apply auxiliary support jigs, position clamps close to cutting zones, and optimize machining sequence: rough‑mill all features first before finishing thin‑wall regions.
2. Tool setup: Minimize tool overhang for deep‑cavity milling. Long tool overhang magnifies deflection and vibration. Clean spindle tapers and tool holders strictly, keep tool run‑out tightly controlled. Use coated carbide end‑mills; high‑speed‑steel tools wear extremely fast on 32‑38 HRC 718H material.
3. Cutting parameters: Do not only drop feed rate once vibration appears. Excessively low feed causes rubbing work‑hardening on workpiece surface, accelerating tool failure. Fine‑tune spindle RPM to jump out resonance frequency range. Reduce radial depth of cut appropriately while maintaining reasonable feed‑per‑tooth.
Note: There is no universal stable RPM setting for 718H hard milling. Stability windows shift for different machine tools, tool lengths and clamping conditions. Shops should run small trial cuts to tune parameters for their setup.
6. Why Select 718H for Injection Mold Fabrications?
718H’s core advantage is balanced comprehensive performance: uniform through‑section hardness, reliable polish‑and‑texture performance, sufficient toughness and predictable total project cost. It avoids two common material traps: P20’s poor core hardness on thick blocks, and the steep price premium of full mirror pre‑hardened steel grades.
For large‑size molds requiring CNC hard milling plus cosmetic surface treatment, 718H provides an economical, low‑risk starting point.
On the flip side, 718H is not suitable for scenarios with heavy corrosion risk (PVC, flame‑retardant plastics) or extremely high glass‑fiber filler content. For those cases choose S136 stainless mold steel or wear‑resistant tool steel, or apply nitriding / chrome‑plating surface treatments to 718H components.
7. Conclusion
718H (DIN 1.2738) remains the mainstream pre‑hardened nickel‑alloy mold steel for medium‑to‑large appearance plastic molds. Uniform through‑thickness hardness, good toughness, reliable polishing & etching capability and competitive total‑process cost make it ideal for automotive trim, home‑appliance, cosmetic‑packaging and consumer‑electronic injection‑mold inserts.
When CNC‑machining deep‑cavity or thin‑rib 718H mold blocks, pay close attention to system rigidity, tool selection and chatter risks. Working with a supplier offering end‑to‑end services including block supply, CNC hard‑milling and mold‑steel pre‑treatment can greatly simplify your procurement cycle.
For latest 718H mold block stock sizes and processing service pricing, please check our product page. Reach out to our technical sales team for custom quotation.
FAQ
Q1. What is the difference between 718H and P20 mold steel?
718H is nickel‑added upgraded version of P20, delivered at higher pre‑hardened hardness 32‑38 HRC with much better hardness uniformity on thick mold blocks, superior polish‑and‑texturing quality and longer mold‑life. Specify full grade “718H” on drawings for mold projects with thick blocks and cosmetic‑part requirements
Q2. How about the machinability of 718H?
718H has moderate machinability for pre-hardened mold steel. Coated‑carbide cutting tools are mandatory. Watch for milling chatter and fast tool wear on thin‑rib deep‑cavity inserts. You must manage clamping rigidity, tool overhang and cutting parameters properly to get stable finishing quality.
Q3. Can we perform texture etching and high‑gloss polishing on 718H?
Yes. One core selling point for 718H is excellent polishing and texturing performance. Proper processing can reach high‑gloss surfaces and fine VDI / Mold‑Tech decorative textures. Poor‑quality substituted steel will produce pitting and uneven texture patterns on cavity surfaces
Q4. What are typical real‑world applications of 718H?
Automotive interior trims, home‑appliance housings, cosmetic‑packaging molds, consumer‑electronic plastic shells and general‑purpose cosmetic injection‑mold inserts for medium‑to‑high volume production runs
Q5. Why does chatter happen during CNC hard‑milling thin‑rib 718H mold inserts?
Thin‑rib mold inserts deflect easily under cutting force and generate regenerative chatter. Optimize clamping method, add auxiliary supports, shorten tool overhang, adopt proper coated‑carbide cutters and fine‑tune spindle speed & cutting depth to stabilize hard‑milling operations
Q6. Is surface treatment needed for 718H when molding corrosive plastic materials?
718H has no native corrosion resistance. For PVC or flame‑retardant plastic molding, nitriding or chrome‑plating surface treatment is required, or switch to stainless mold steel such as S136 for long‑term production

